Casted Flashlight

Made by Taylor Mau

The goal of this project was to build off of the previously created clay flashlight. This is now a resin cast flashlight which was created using silicone molding.

Created: April 17th, 2019

0

By using the clay flashlight made from the last project, I worked on making the clay model into a plastic flashlight. To do this, I made a silicone mold of the flashlight and then cast it in resin. By doing this, I was able to produce three different flashlights. 

0

Silicone Molding Process 

In order to make the flashlight, I needed to make a three-part mold. To do this, I used clay to cover up the areas that I did not want that part of the mold to be in. Since my part was also made out of clay, this proved to be difficult because the white clay that I used to block the silicone stuck to the industrial clay of the flashlight. 

0

After packing the first part clay, I started to build a box around the flashlight to be able to hold the silicone that I was going to be pouring in. Here, the white clay prevents the silicone from going any deeper and this creates the first part of the mold. I also used a pen to poke holes in the white clay. This was for the registration marks. 

0

Then I calculated the amount of silicone to pour into the box. Part A and B were mixed well by scraping the sides of the container and mixing it with a wooden stick. The silicone was poured into the box and I waited for it to cure. 

0

Then, I took off the white clay on the top side of the mold and left the white clay on the right side of the mold. Since I was doing a three-part mold, the white clay on the right-hand side is for the third part of the mold. 

0

After I poured silicone for the last part of the mold, I finally had my three parts of the mold that would create my flashlight. 

0

I then mixed the resin which is a plastic similar to the process of making the silicone. I added pour spouts and an air hole to allow bubbles to escape. After mixing the resin and adding color to it, I then poured it into the mold. I rubberbanded the box together to make sure that the resin did not pour out. As I poured the resin, I made sure to move the silicone box around to try and let some bubbles escape. 

0

Then, I started to remove the mold from the silicone. See the video below. 

0
Demolding the Flashlight
Taylor Mau - https://youtu.be/6ERjsY1oZvE
0

Despite trying to remove the air bubbles, a lot of them actually remained in the part causing small holes to form in the flashlight. This was not ideal so I put the flashlight in the pressure chamber the next time I poured resin and it helped remove more of the bubbles.  

0

First I did a rough sanding of the part. I then hand filed each of the grip lines in the flashlight. This was because I wanted a grip pattern but the pattern that I created did not show up as well as I had hoped. 

0

I then sanded the flashlight through all of the grits of sandpaper that I had. This took about 8 hours since I had to first sand away all of the imperfections of the mold. There were parting lines and because some of the silicone from one part of the mold leaked into the other part of the mold, there were inconsistencies in the shape that needed to be sanded away. 

0

I then created three more prototypes. The leftmost prototype is how the flashlight looks when it comes out of the mold. The green flashlight in the middle represents a rough sanded one. The flashlight on the end is the fully sanded one and has the electrical components inside. 

0

Bonus

I also added in an electrical circuit to complete the flashlight. I created the circuit using a reed switch. The reed switch completes the circuit when there is a magnet nearby.

0
Flashlight Working
Taylor Mau - https://youtu.be/-2rADRbYQ2A
x
Share this Project

Found In
Courses

24-672 Special Topics in DIY Design and Fabrication

· 22 members

Offers students hands-on experience in DIY product design and fabrication processes. Students work individually or in small groups to design customized and personalized products of their own and bu...more


About

The goal of this project was to build off of the previously created clay flashlight. This is now a resin cast flashlight which was created using silicone molding.